#ifndef _BOARD_H #define _BOARD_H /********** display configuration **********/ #define LCD_INTERFACE_TTL 0 #define LCD_INTERFACE_LVDS 1 #define LCD_INTERFACE_CPU 2 #define LCD_INTERFACE_MIPI 3 #define LCD_WIRING_MODE_RGB 0 #define LCD_WIRING_MODE_RBG 1 #define LCD_WIRING_MODE_GRB 2 #define LCD_WIRING_MODE_GBR 3 #define LCD_WIRING_MODE_BRG 4 #define LCD_WIRING_MODE_BGR 5 #define LCD_WIRING_BIT_ORDER_MSB 0 #define LCD_WIRING_BIT_ORDER_LSB 1 #define LVDS_PANEL_FORMAT_VESA 0 #define LVDS_PANEL_FORMAT_JEDIA 1 #define LVDS_PANEL_DATA_8BIT 0 #define LVDS_PANEL_DATA_6BIT 1 #define LVDS_CLKEDGE_POSITIVE 0 #define LVDS_CLKEDGE_NEGATIVE 1 #define CPU_PANEL_18BIT_MODE 0 #define CPU_PANEL_16BIT_MODE 1 #define CPU_PANEL_9BIT_MODE 2 #define CPU_PANEL_8BIT_MODE 3 #define LCD_ROTATE_ANGLE_0 0 #define LCD_ROTATE_ANGLE_90 1 #define LCD_ROTATE_ANGLE_180 2 #define LCD_ROTATE_ANGLE_270 3 #define LCD_H_FLIP 0 //水平镜像 #define LCD_V_FLIP 0 //垂直镜像 //#define LCD_CLK_INVERSE //LCD时钟极性反向 #define LCD_ROTATE_ANGLE LCD_ROTATE_ANGLE_0 #define LCD_WIDTH 1920 #define LCD_HEIGHT 720 #define LCD_BPP 32 #define LCD_INTERFACE_TYPE LCD_INTERFACE_LVDS #define DOUBLE_LVDS_ENABLE 1 #if !DOUBLE_LVDS_ENABLE #define SINGLE_LVDS_CH0_EN 1 #define SINGLE_LVDS_CH1_EN 0 #endif #if LCD_INTERFACE_TYPE == LCD_INTERFACE_TTL #define LCD_WIRING_MODE LCD_WIRING_MODE_RGB //#define LCD_WIRING_BIT_ORDER LCD_WIRING_BIT_ORDER_LSB #define LCD_WIRING_BIT_ORDER LCD_WIRING_BIT_ORDER_MSB #elif LCD_INTERFACE_TYPE == LCD_INTERFACE_LVDS #define LCD_WIRING_MODE LCD_WIRING_MODE_RGB #define LCD_WIRING_BIT_ORDER LCD_WIRING_BIT_ORDER_MSB #define LVDS_PANEL_FORMAT LVDS_PANEL_FORMAT_VESA #define LVDS_PANEL_DATA LVDS_PANEL_DATA_8BIT #define LVDS_CLKEDGE LVDS_CLKEDGE_POSITIVE #define LVDS_SCREEN_RST_GPIO 74 #elif LCD_INTERFACE_TYPE == LCD_INTERFACE_CPU #define CPU_PANEL_DATA CPU_PANEL_8BIT_MODE #elif LCD_INTERFACE_TYPE == LCD_INTERFACE_MIPI #define LCD_WIRING_MODE LCD_WIRING_MODE_RGB #define LCD_WIRING_BIT_ORDER LCD_WIRING_BIT_ORDER_MSB #endif #define FB_SIZE (LCD_WIDTH * LCD_HEIGHT * LCD_BPP / 8) #define VIDEO_DISPLAY_WIDTH ((LCD_WIDTH + 15) & (~0xF)) #define VIDEO_DISPLAY_HEIGHT ((LCD_HEIGHT + 15) & (~0xF)) #define VIDEO_DISPLAY_BUF_NUM 2 #if (LCD_WIDTH == 1024 && LCD_HEIGHT == 600) #define LCD_TIMING_VBP 1 #define LCD_TIMING_VFP 1 #define LCD_TIMING_VSW 30 #define LCD_TIMING_HBP 100 #define LCD_TIMING_HFP 100 #define LCD_TIMING_HSW 370 #define LCD_CLK_FREQ 50000000 #elif (LCD_WIDTH == 1920 && LCD_HEIGHT == 720) #define LCD_TIMING_VBP 11 #define LCD_TIMING_VFP 14 #define LCD_TIMING_VSW 7 #define LCD_TIMING_HBP 38*2 #define LCD_TIMING_HFP 30*2 #define LCD_TIMING_HSW 36*2 #define LCD_CLK_FREQ 96000000 #elif (LCD_WIDTH == 800 && LCD_HEIGHT == 480) #define LCD_TIMING_VBP 1 #define LCD_TIMING_VFP 1 #define LCD_TIMING_VSW 30 #define LCD_TIMING_HBP 50 #define LCD_TIMING_HFP 50 #define LCD_TIMING_HSW 180 #define LCD_CLK_FREQ 35000000 #elif (LCD_WIDTH == 1280 && LCD_HEIGHT == 720) #define LCD_TIMING_VBP 5 #define LCD_TIMING_VFP 65 #define LCD_TIMING_VSW 2 #define LCD_TIMING_HBP 16 #define LCD_TIMING_HFP 42 #define LCD_TIMING_HSW 2 #define LCD_CLK_FREQ 60000000 #elif (LCD_WIDTH == 1280 && LCD_HEIGHT == 480) #define LCD_TIMING_VBP 5 #define LCD_TIMING_VFP 8 #define LCD_TIMING_VSW 3 #define LCD_TIMING_HBP 16 #define LCD_TIMING_HFP 28 //26 #define LCD_TIMING_HSW 12 #define LCD_CLK_FREQ 40000000 #elif (LCD_WIDTH == 480 && LCD_HEIGHT == 1280) #define LCD_TIMING_VBP 6// 14 #define LCD_TIMING_VFP 6// 16 #define LCD_TIMING_VSW 16// 2 #define LCD_TIMING_HBP 16 #define LCD_TIMING_HFP 36 #define LCD_TIMING_HSW 26 #define LCD_CLK_FREQ 50000000 #else #error "no lcd timing configuraion." #endif /*******************************************/ /************ adc configuration ************/ //#define ADC_TOUCH //#define ADC_KEY /*******************************************/ /******* video in configuration *******/ #define VIDEO_DECODER_RN6752 //#define VIDEO_DECODER_MIPI //#define VIDEO_DECODER_ARK7116M //#define VIDEO_DECODER_ARK7116 #define VIN_CVBS_PAL 0 #define VIN_CVBS_NTSC 1 #define VIN_AHD_720P_25 2 #define VIN_AHD_720P_30 3 #define VIN_AHD_1080P_25 4 #define VIN_AHD_1080P_30 5 #define VIDEO_IN_FORMAT VIN_AHD_720P_25//VIN_CVBS_NTSC #if VIDEO_IN_FORMAT == VIN_CVBS_PAL #define VIN_WIDTH 720 #define VIN_HEIGHT 288 #elif VIDEO_IN_FORMAT == VIN_CVBS_NTSC #define VIN_WIDTH 720 #define VIN_HEIGHT 240 #elif VIDEO_IN_FORMAT == VIN_AHD_720P_25 || VIDEO_IN_FORMAT == VIN_AHD_720P_30 #define VIN_WIDTH 1280 #define VIN_HEIGHT 720 #elif VIDEO_IN_FORMAT == VIN_AHD_1080P_25 || VIDEO_IN_FORMAT == VIN_AHD_1080P_30 #define VIN_WIDTH 1920 #define VIN_HEIGHT 1080 #endif #if VIN_WIDTH * VIN_HEIGHT > 0x96000 #define VIN_SMALL_MEM #endif /*******************************************/ /************ carback configuration ********/ //#define CARBACK_DETECT /*******************************************/ /********* touchscreen configuration *******/ //#define TP_SUPPORT /********* wrap configuration *******/ //#define WRAP_SUPPORT #ifdef TP_SUPPORT /* Select one tp IC */ //#define TP_USE_GT9XX //#define TP_USE_GA657X //#define TP_USE_FT6336U /* Config tp parameters */ #define TP_GPIO_INT 4 #define TP_GPIO_RST 5 #define TP_INV_X 0 #define TP_INV_Y 0 #define TP_INV_XY_AXIS 0 //翻转XY轴 #define TP_MT_TOUCH 0 //支持多点触摸 #endif /*******************************************/ /*********** sdmmc configuration ***********/ #define SDMMC0_SUPPORT #define SDMMC1_SUPPORT #if defined(SDMMC0_SUPPORT) || defined(SDMMC1_SUPPORT) #define SDMMC_SUPPORT #endif /*******************************************/ /*********** uart configuration ************/ #define UART_MCU_PORT 3 #define UART_DEBUG_PORT UART_ID0 /*******************************************/ /************ rtc configuration ************/ //#define RTC_SUPPORT /*******************************************/ /************ remote configuration ************/ //#define REMOTE_SUPPORT /*******************************************/ /************ pwm capture configuration ************/ //#define PWM_CAP_SUPPORT /*******************************************/ /************ i2c configuration ************/ #define DW_I2C0_SUPPORT //#define DW_I2C1_SUPPORT //#define ANALOG_I2C_SUPPORT #define I2C_GPIO0_SDA_PIN 66 #define I2C_GPIO0_SCL_PIN 65 /*******************************************/ /************ dw spi configuration ************/ #define DW_SPI0_SUPPORT #define DW_SPI2_SUPPORT /*******************************************/ /************ ecspi configuration ************/ #define EC_SPI1_SUPPORT /*******************************************/ /************ dma configuration ************/ /* the smaller channel has higher priority */ #define SPI0_RX_DMA_CH 0 #define I2S_DMA_RXCH 3 #define I2S_DMA_TXCH 4 #define I2S1_DMA_RXCH I2S_DMA_RXCH #define I2S1_DMA_TXCH I2S_DMA_TXCH #define ECSPI_TX_DMA_CH 5 #define ECSPI_RX_DMA_CH 6 /*******************************************/ /************ usb configuration ************/ #define USB_SUPPORT #define USB_MODE_ID -1 //#define USB_DMA //#define USB_UVC_SUPPORT #define CONFIG_USB_DWC2_HOST 1 #define CONFIG_USB_NEW_DWC2_HOST 1 #define CONFIG_USB_DWC2_PERIPHERAL 1 #define CONFIG_USB_NEW_DWC2_GADGET 1 #if USB_MODE_ID && USB_MODE_ID != -1 #define CONFIG_USB_DEVICE_CDC_NCM 1 #endif /*******************************************/ /************ carlink configuration ************/ #ifdef CARLINK_ENABLE /* define in iar options */ #define WIFI_SUPPORT #endif #ifdef WIFI_SUPPORT #define CARLINK_EY 0 #define CARLINK_EC 1 #define WIFI_RESET_IO 95 #else #define CARLINK_EY 0 #define CARLINK_EC 0 #endif #if CARLINK_EY && CARLINK_EC #error "Do not choose two car links" #endif #if CARLINK_EC == 1 #define USE_LWIP 1 #else #define USE_LWIP 0 #endif #define BT_RESET_IO 94 #define BT_UART_PORT 1 //#define RELTECK_WIFI_AP_MODE /*******************************************/ /************ audio configuration ************/ #define I2S_ID0 0 #define I2S_ID1 1 #define I2S_NUMS 2 /* add your adc type */ #define AUDIO_CODEC_ADC_NONE 0 //Not use codec adc ic or no need driver. #define AUDIO_CODEC_ADC_ES7243E 1 //Use codec adc ic es7243e. /* add your dac type */ #define AUDIO_CODEC_DAC_NONE 0 //Not use codec adc ic or no need driver. #define AUDIO_CODEC_DAC_ES8156 1 //Use codec dac ic es8156. /* choose your audio use type */ //#define AUDIO_REPLAY //#define AUDIO_RECORD #ifdef AUDIO_REPLAY #define AUDIO_REPLAY_I2S I2S_ID0 /* Select i2s id */ #define AUDIO_CODEC_DAC_IC AUDIO_CODEC_DAC_NONE /* Select your codec dac type */ #endif #ifdef AUDIO_RECORD #define AUDIO_RECORD_I2S I2S_ID1 /* Select i2s id */ #define AUDIO_CODEC_ADC_IC AUDIO_CODEC_ADC_ES7243E /* Select your codec adc type */ #endif #ifndef AUDIO_CODEC_DAC_IC #define AUDIO_CODEC_DAC_IC AUDIO_CODEC_DAC_NONE /* Do not use codec dac by default */ #endif #ifndef AUDIO_CODEC_ADC_IC #define AUDIO_CODEC_ADC_IC AUDIO_CODEC_ADC_NONE /* Do not use codec adc by default */ #endif #if (AUDIO_CODEC_DAC_IC == AUDIO_CODEC_DAC_ES8156) #define AUDIO_CODEC_DAC_NAME "ES8156" #else #define AUDIO_CODEC_DAC_NAME "" #endif #if (AUDIO_CODEC_ADC_IC == AUDIO_CODEC_ADC_ES7243E) #define AUDIO_CODEC_ADC_NAME "ES7243E" #else #define AUDIO_CODEC_ADC_NAME "" #endif /*******************************************/ /********** mailbox configuration **********/ #define MAILBOX_SUPPORT /*******************************************/ /************ eth configuration ************/ /* 系统使用LWIP协议栈还是FREERTOS_TCP协议栈由宏“USE_LWIP”决定 */ //#define ETH_SUPPORT #define FREERTOS_TCP_ETH_EN 0 #define LWIP_ETH_EN 1 /*******************************************/ /********** romfile configuration **********/ /* 没有定义ROMFILE_USE_SMALL_MEM，romfile内容会全部加载到ddr * 内存不足时可以定义ROMFILE_USE_SMALL_MEM节省内存使用 */ #define ROMFILE_USE_SMALL_MEM #ifndef ROMFILE_USE_SMALL_MEM /* 定义READ_ROMFILE_ONCE，romfile内容会整个一次加载到ddr，如果 * 文件过大会导致启动时间慢 */ //#define READ_ROMFILE_ONCE #else /* 缓存在DDR里的文件数，未缓存的文件需要重新从flash里读取 */ #define ROMFILE_CACHE_DEF_SIZE 0 #endif /*******************************************/ /********** animation configuration **********/ #define ANIMATION_NONE 0 #define ANIMATION_USE_SMALL_MEM 1 #define ANIMATION_NORMAL 2 #define ANIMATION_POLICY ANIMATION_NORMAL /*********************************************/ /************ flash type configuration ************/ #define SPI_NOR_FLASH 0 #define SPI_NAND_FLASH 1 #define EMMC_FLASH 2 #define DEVICE_TYPE_SELECT EMMC_FLASH #if DEVICE_TYPE_SELECT != EMMC_FLASH //#define SPI0_QSPI_MODE #else #define DEVICE_PARTITION_NAME "/emmc" #endif /*******************************************/ /********** update mode configuration **********/ #define OTA_UPDATE_SUPPORT #ifdef OTA_UPDATE_SUPPORT #define IMAGE_RESOURCES_BACKUP //#define DELTA_UPDATE_SUPPORT #define MAILBOX_UPDATE_SUPPORT //#define WIFI_UPDATE_SUPPORT #if defined(WIFI_UPDATE_SUPPORT) && !defined(USB_SUPPORT) #error "Error! Should define USB_SUPPORT to support wifi simu update" #endif //#define NCM_UPDATE_SUPPORT #if defined(NCM_UPDATE_SUPPORT) && !CONFIG_USB_DEVICE_CDC_NCM #error "Error! Should define CONFIG_USB_DEVICE_CDC_NCM=1 to support ncm update" #endif //#define NCM_LOG_SUPPORT #if defined(NCM_LOG_SUPPORT) && !CONFIG_USB_DEVICE_CDC_NCM #error "Error! Should define CONFIG_USB_DEVICE_CDC_NCM=1 to support ncm log" #endif #else #error "Error! Should define OTA_UPDATE_SUPPORT to support other update options" #endif /*********************************************/ /********** update address configuration **********/ #if DEVICE_TYPE_SELECT == SPI_NOR_FLASH #define MCU_RESERVE_SIZE 0x100000ul //1MB #define SYSINFO_MAX_SIZE 0x1000 //4KB #define LOADER_MAX_SIZE 0x8000 //32KB #define APPFILE_MAX_SIZE 0x200000 //2MB #define ANIMFILE_MAX_SIZE 0x500000 //5MB #define ROMFILE_MAX_SIZE 0x1000000 //16MB #define OTA_MEDIA_SIZE 0xa00000 //10MB /********************************************************************************************************************************** spi nor flash address space( 0 address start)-(resources AB backup) |-----1MB-----|---4KB---|---4KB---|--32KB--|--32KB--|---2MB---|---5MB---|---16MB---|---2MB---|---5MB---|---16MB---|---10MB---|---end |-------------|---------|---------|--------|--------|---------|---------|----------|---------|---------|----------|----------| |0 |0x100000 |0x101000 |0x102000|0x10A000|0x112000 |0x312000 | 0x812000 |0x1812000|0x1A12000|0x1F12000 |0x2F12000 | |MCU reserved | SYSINFO |SYSINFO B| AMTLDR |AMTLDR B| APP | ANIM | ROM | APP B | ANIM B | ROM B | OTA | |_____________|_________|_________|________|________|_________|_________|__________|_________|_________|__________|__________| spi nor flash address space( 0 address start) |-----1MB-----|---4KB---|---4KB---|--32KB--|--32KB--|---2MB---|---5MB---|---16MB---|---2MB---|---5MB---|---end |-------------|---------|---------|--------|--------|---------|---------|--------- |---------|---------| |0 |0x100000 |0x101000 |0x102000|0x10A000|0x112000 |0x312000 | 0x812000 |0x1812000|0x1A12000| |MCU reserved | SYSINFO |SYSINFO B| AMTLDR |AMTLDR B| APP | ANIM | ROM | APP B | OTA | |_____________|_________|_________|________|________|_________|_________|__________|_________|_________| ***********************************************************************************************************************************/ #elif DEVICE_TYPE_SELECT == EMMC_FLASH #define MCU_RESERVE_SIZE 0x1000000ul //16MB #define SYSINFO_MAX_SIZE 0x80000 //512KB #define LOADER_MAX_SIZE 0x80000 //512KB #define APPFILE_MAX_SIZE 0x1000000 //16MB #define ANIMFILE_MAX_SIZE 0x500000 //5MB #define ROMFILE_MAX_SIZE 0x8000000 //128MB #define OTA_MEDIA_SIZE 0x10000000 //256MB /*********************************************************************************************************************************** emmc address space( 0 address start)-(resources AB backup) |----16MB-----|---512KB---|---512KB---|---512KB---|---512KB---|---16MB---|---5MB---|---128MB--|---16MB---|---5MB----|---128MB---|--256MB---|---end |-------------|-----------|-----------|-----------|-----------|----------|---------|----------|----------|----------|-----------|----------| |0 | 0x1000000 | 0x1080000 | 0x1100000 | 0x1180000 |0x1200000 |0x2200000|0x2700000 |0xA700000 |0xB700000 | 0xBC00000 |0x13C00000| |MCU reserved | SYSINFO | SYSINFO B | AMTLDR | AMTLDR B | APP | ANIM | ROM | APP B | ANIM B | ROM B | OTA | |_____________|___________|___________|___________|___________|__________|_________|__________|__________|__________|___________|__________| emmc address space( 0 address start) |----16MB-----|---512KB---|---512KB---|---512KB---|---512KB---|---16MB---|---5MB---|---128MB--|---16MB---|--256MB---|---end |-------------|-----------|-----------|-----------|-----------|----------|---------|----------|----------|----------| |0 | 0x1000000 | 0x1080000 | 0x1100000 | 0x1180000 |0x1200000 |0x2200000|0x2700000 |0xA700000 |0xB700000 | |MCU reserved | SYSINFO | SYSINFO B | AMTLDR | AMTLDR B | APP | ANIM | ROM | APP B | OTA | |_____________|___________|___________|___________|___________|__________|_________|__________|__________|__________| *************************************************************************************************************************************/ #else #error "Invalid flash type." #endif #define SYSINFO_OFFSET MCU_RESERVE_SIZE #define SYSINFO_B_OFFSET (SYSINFO_OFFSET + SYSINFO_MAX_SIZE) #define LOADER_OFFSET (SYSINFO_B_OFFSET + SYSINFO_MAX_SIZE) #define LOADER_B_OFFSET (LOADER_OFFSET + LOADER_MAX_SIZE) #define APPFILE_OFFSET (LOADER_B_OFFSET + LOADER_MAX_SIZE) #define ANIMFILE_OFFSET (APPFILE_OFFSET + APPFILE_MAX_SIZE) #define ROMFILE_OFFSET (ANIMFILE_OFFSET + ANIMFILE_MAX_SIZE) #define APPFILE_B_OFFSET (ROMFILE_OFFSET + ROMFILE_MAX_SIZE) #ifdef IMAGE_RESOURCES_BACKUP #define ANIMFILE_B_OFFSET (APPFILE_B_OFFSET + APPFILE_MAX_SIZE) #define ROMFILE_B_OFFSET (ANIMFILE_B_OFFSET + ANIMFILE_MAX_SIZE) #define OTA_MEDIA_OFFSET (ROMFILE_B_OFFSET + ROMFILE_MAX_SIZE) #else #define ANIMFILE_B_OFFSET ANIMFILE_OFFSET #define ROMFILE_B_OFFSET ROMFILE_OFFSET #define OTA_MEDIA_OFFSET (APPFILE_B_OFFSET + APPFILE_MAX_SIZE) #endif /*********************************************/ /************ DDR config configuration ************/ #define DDR_BASE 0x60000000ul #define DDR_TOTAL_SIZE 0x8000000 //128MB #define DDR_DRV_USE_SIZE 0x800000 //8MB #define DDR_MCU_ACCESS_MODULE_SIZE 0x40000 //256KB #define DDR_CPU_ACCESS_MODULE_SIZE 0x40000 //256KB #define DDR_MEDIA_USE_SIZE 0x80000 //512KB #if DEVICE_TYPE_SELECT == SPI_NOR_FLASH #define DDR_CAN_UPDATE_SIZE 0x200000 //2MB #define DDR_RESERVED_SIZE 0x500000 //5MB #elif DEVICE_TYPE_SELECT == EMMC_FLASH #define DDR_CAN_UPDATE_SIZE 0x400000 //4MB #define DDR_RESERVED_SIZE 0x300000 //3MB #endif #define DDR_DRV_USE_ADDR (DDR_BASE + DDR_TOTAL_SIZE - DDR_DRV_USE_SIZE) #define DDR_MCU_ACCESS_MODULE_ADDR (DDR_DRV_USE_ADDR) #define DDR_CPU_ACCESS_MODULE_ADDR (DDR_MCU_ACCESS_MODULE_ADDR + DDR_MCU_ACCESS_MODULE_SIZE) #define DDR_MEDIA_USE_ADDR (DDR_CPU_ACCESS_MODULE_ADDR + DDR_CPU_ACCESS_MODULE_SIZE) #define DDR_CAN_USE_ADDR (DDR_MADIA_USE_ADDR + DDR_MEDIA_USE_SIZE) /********************************************************************* spi nor flash DDR address space |----120MB----|------256KB------|------256KB------|----512KB----|-----2MB-----|-----5MB-----|---end |-------------|-----------------|-----------------|-------------|-------------|-------------| |0x60000000 |0x67800000 |0x67840000 |0x67880000 |0x67900000 |0x67B00000 | |CPU USE |MCU Access module|CPU Access module|Media update |Can update |Reserved | |_____________|_________________|_________________|_____________|_____________|_____________| *********************************************************************** emmc DDR address space |----120MB----|------256KB------|------256KB------|----512KB----|-----4MB-----|-----3MB-----|---end |-------------|-----------------|-----------------|-------------|-------------|-------------| |0x60000000 |0x67800000 |0x67840000 |0x67880000 |0x67900000 |0x67D00000 | |CPU USE |MCU Access module|CPU Access module|Media update |Can update |Reserved | |_____________|_________________|_________________|_____________|_____________|_____________| **********************************************************************/ /*********************************************/ /********** ulog configuration **********/ //#define USE_ULOG #define ULOG_NAME_MAX 8 #define ULOG_LINE_BUF_SIZE 1024 #define ULOG_OUTPUT_LEVEL #define ULOG_OUTPUT_TIME //#define ULOG_TIME_USING_TIMESTAMP //#define ULOG_OUTPUT_TAG //#define ULOG_USING_COLOR #define ULOG_USING_ISR_LOG #define ULOG_BACKEND_USING_CONSOLE #define ULOG_EASYFLASH_BACKEND_ENABLE #ifdef ULOG_EASYFLASH_BACKEND_ENABLE #define EASYFLASH_LOG #if DEVICE_TYPE_SELECT != EMMC_FLASH #define EASYFLASH_LOG_AREA_SIZE 0x100000 #define EASYFLASH_ERASE_GRAN 0x1000 #define EASYFLASH_WRITE_GRAN 0x100 #define EASYFLASH_START_ADDR 0x1700000 #else #define EASYFLASH_LOG_AREA_SIZE 0x100000 #define EASYFLASH_ERASE_GRAN 0x10000 #define EASYFLASH_WRITE_GRAN 0x200 #define EASYFLASH_START_ADDR 0x60000000 #endif #endif //#define ULOG_FILE_BACKEND_ENABLE #ifdef ULOG_FILE_BACKEND_ENABLE #if DEVICE_TYPE_SELECT != EMMC_FLASH #define ULOG_FILE_ROOT_PATH "/sf/logs" #else #define ULOG_FILE_ROOT_PATH "/emmc/logs" #endif #define ULOG_FILE_NAME_BASE "ulog.log" #define ULOG_FILE_MAX_NUM 10 #define ULOG_FILE_MAX_SIZE (1024 * 32) #endif //#define ULOG_USING_ASYNC_OUTPUT //ulog异步输出 #define ULOG_ASYNC_OUTPUT_BUF_SIZE 32768 //32K #define ULOG_ASYNC_OUTPUT_THREAD_STACK 2048 #define ULOG_ASYNC_OUTPUT_THREAD_PRIORITY 10 /*********************************************/ #endif