ark1668ed-bsp/u-boot/arch/powerpc/dts/gazerbeam.dts

/*
 * Gazerbeam CON Device Tree Source
 *
 * (C) Copyright 2015
 * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de
 *
 * This program is free software; you can redistribute  it and/or modify it
 * under  the terms of  the GNU General  Public License as published by the
 * Free Software Foundation;  either version 2 of the  License, or (at your
 * option) any later version.
 */

#include "gdsys/mpc8308.dtsi"

/include/ "gdsys/gazerbeam-base.dtsi"

/include/ "gdsys/soc/i2c/cirrus-audio-codec.dtsi"
/include/ "gdsys/soc/i2c/dallas-rtc.dtsi"
/include/ "gdsys/soc/lbc/gazerbeam.dtsi"
/include/ "gdsys/soc/nor/flash-80k-partition.dtsi"

&board_lbc {
	FPGA0:iocon_uart@1,0 {
		reg = <0x1 0x0 0x100000>;
		little-endian;
		interrupts = <48 0x8>;
		interrupt-parent = <&ipic>;
	};

	FPGA1:iocon_uart@2,0 {
		reg = <0x2 0x0 0x100000>;
		little-endian;
		interrupts = <17 0x8>;
		interrupt-parent = <&ipic>;
	};
};

&FPGA0 {
	compatible = "gdsys,iocon_fpga";
	#gpio-cells = <2>;
	gpio-controller;
	bus = <&FPGA0BUS>;
	unit_id = <0>;
	fpga-type = <1>;
	usb_base = <0x0080>;
	audio_base = <0x0040>;
	timebase_base = <0x013c>;

	/*
	 * for every interrupt source there must be a dataset specifying
	 * 1. type (1: standard)
	 * 2. status register offset
	 * 3. mask register offset
	 * 4. default mask
	 */
	fpga_interrupt_sources =
		<1 0x000a 0x000c 0x4000>, /* 0: TOP_INTERRUPT */
		<1 0x001c 0x001e 0x0000>; /* 1: EXTENDED_INTERRUPT */
	/*
	 * for every interrupt there must be a dataset specifying
	 * 1. type (1: status, 2: event)
	 * 2. interrupt source index
	 * 3. interrupt register bit
	 * 4. mask register bit
	 */
	 #fpga_interrupt_map-cells = <4>;
	fpga_interrupt_map =
		<1 0 14 14>, /*  0: EXTENDED_INTERRUPT */
		<1 0  0  0>, /*  1: VIDEO 0 */
		<1 0  1  1>, /*  2: VIDEO 1 */
		<1 0  2  2>, /*  3: VIDEO IC 0 */
		<1 0  3  3>, /*  4: VIDEO IC 1 */
		<1 0  4  4>, /*  5: IIC MAIN */
		<1 0  6  6>, /*  6: IIC VIDEO 0 */
		<1 0  7  7>, /*  7: IIC VIDEO 1 */
		<1 1  0  0>, /*  8: OSD 0 */
		<1 1  1  1>, /*  9: OSD 1 */
		<1 1  2  2>, /* 10: SPDIF 0 */
		<1 1  3  3>, /* 11: SPDIF 1 */
		<1 0 12 12>, /* 12: COMM 0 */
		<1 0 13 13>, /* 13: COMM 1 */
		<1 0 10 10>, /* 14: COMM 2 */
		<1 0 11 11>, /* 15: COMM 3 */
		<2 0  5  5>, /* 16: MDIO */
		<1 0  8  8>, /* 17: PHY */
		<1 1  4  4>, /* 18: RS232 */
		<1 1  5  5>, /* 19: AUDIO */
		<1 1  8  8>, /* 20: PROC_AUDIO */
		<1 1  7  7>, /* 21: USB/ETH-UART INT */
		<2 1 10 10>, /* 22: AXI Bridge 0 */
		<2 1 11 11>, /* 23: AXI Bridge 1 */
		<2 1  9  9>, /* 24: USB/ETH-Secondary IIC */
		<>;
};

&FPGA1 {
	compatible = "gdsys,iocon_fpga";
	#gpio-cells = <2>;
	gpio-controller;
	bus = <&FPGA1BUS>;
	unit_id = <1>;
	fpga-type = <1>;
	usb_base = <0x0070>;
	audio_base = <0x0040>;
	timebase_base = <0x013c>;

	/*
	 * for every interrupt source there must be a dataset specifying
	 * 1. type (1: standard)
	 * 2. status register offset
	 * 3. mask register offset
	 * 4. default mask
	 */
	fpga_interrupt_sources =
		<1 0x000a 0x000c 0x4000>, /* 0: TOP_INTERRUPT */
		<1 0x001c 0x001e 0x0000>; /* 1: EXTENDED_INTERRUPT */
	/*
	 * for every interrupt there must be a dataset specifying
	 * 1. type (1: status, 2: event)
	 * 2. interrupt source index
	 * 3. interrupt register bit
	 * 4. mask register bit
	 */
	 #fpga_interrupt_map-cells = <4>;
	fpga_interrupt_map =
		<1 0 14 14>, /*  0: EXTENDED_INTERRUPT */
		<1 0  0  0>, /*  1: VIDEO 0 */
		<1 0  1  1>, /*  2: VIDEO 1 */
		<1 0  2  2>, /*  3: VIDEO IC 0 */
		<1 0  3  3>, /*  4: VIDEO IC 1 */
		<1 0  4  4>, /*  5: IIC MAIN */
		<1 0  6  6>, /*  6: IIC VIDEO 0 */
		<1 0  7  7>, /*  7: IIC VIDEO 1 */
		<1 1  0  0>, /*  8: OSD 0 */
		<1 1  1  1>, /*  9: OSD 1 */
		<1 1  2  2>, /* 10: SPDIF 0 */
		<1 1  3  3>, /* 11: SPDIF 1 */
		<1 0 12 12>, /* 12: COMM 0 */
		<1 0 13 13>, /* 13: COMM 1 */
		<1 0 10 10>, /* 14: COMM 2 */
		<1 0 11 11>, /* 15: COMM 3 */
		<2 0  5  5>, /* 16: MDIO */
		<1 0  8  8>, /* 17: PHY */
		<1 1  4  4>, /* 18: RS232 */
		<1 1  5  5>, /* 19: AUDIO */
		<1 1  8  8>, /* 20: PROC_AUDIO */
		<1 1  7  7>, /* 21: USB/ETH-UART INT */
		<2 1 10 10>, /* 22: AXI Bridge 0 */
		<2 1 11 11>, /* 23: AXI Bridge 1 */
		<2 1  9  9>, /* 24: USB/ETH-Secondary IIC */
		<>;
};

/ {
	FPGA0BUS: fpga0bus {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges = <0 0 0x00002000>;

		compatible = "gdsys,soc";

		fpga0_rs232 {
			compatible = "gdsys,ihs_trans_rs232";
			reg = <0x50 0x08>;
			little-endian;
		};

		fpga0_uart_usb {
			compatible = "gdsys,ihs_simple_uart";
			reg = <0xa0 0x08>;
			little-endian;
			fpga_interrupts = <21>;
			line = <0>;
		};

		fpga0_iic_main {
			compatible = "gdsys,ihs_i2cmaster";
			reg = <0x60 0x10>;
			little-endian;
			fpga_interrupts = <5>;
			#address-cells = <1>;
			#size-cells = <0>;

			fpga0_dp_video0_redriver: fpga0_dp_video0_redriver {
				compatible = "ti,sn75dp130";
				reg = <0x2c>;
				eq-i2c-enable = <3 2 1 0
						 3 2 1 0
						 3 2 1 0
						 3 2 1 0>; /* 3.5 dB for all pe values for all lanes */
			};
			fpga0_dp_video1_redriver: fpga0_dp_video1_redriver {
				compatible = "ti,sn75dp130";
				reg = <0x2e>;
				eq-i2c-enable = <3 2 1 0
						 3 2 1 0
						 3 2 1 0
						 3 2 1 0>; /* 3.5 dB for all pe values for all lanes */
			};
			lm77@48 {
				compatible = "national,lm77";
				reg = <0x48>;
			};
			ads1015@49 {
				compatible = "ti,ads1015";
				reg = <0x49>;
			};
			ads1015@4b {
				compatible = "ti,ads1015";
				reg = <0x4b>;
			};
		};

		fpga0_video0 {
			compatible = "gdsys,ihs_video_out";
			reg = <0x100 0x40>;
			little-endian;
			fpga_interrupts = <1 8>; /* VIDEO OSD */
			osd_base = <0x180>;
			osd_buffer_base = <0x1000>;
			spdif_audio_base = <0x1e0>;
			video_index = <0>;
			video_id = <0>;
			fpga-force-pos-pol;
			sync-source;
			fpga-pb-pixels = <2730>; /* 8192 / 3 */
			fpga-ra-lines = <2>;
			video_tx = <&fpga0_dp_video0>;
			clk_gen = <&fpga0_video0_clkgen>;
			ddc_ci = <&fpga0_dp_video0>;
		};

		fpga0_iic_video0  {
			compatible = "gdsys,ihs_i2cmaster";
			reg = <0x1c0 0x10>;
			little-endian;
			fpga_interrupts = <6>;
			#address-cells = <1>;
			#size-cells = <0>;

			fpga0_video0_clkgen: fpga0_video0_clkgen {
				compatible = "idt,ics8n3qv01";
				reg = <0x6e>;
				channel = <0>;
			};
		};

		fpga0_axi_video0 {
			#address-cells = <1>;
			#size-cells = <1>;
			compatible = "gdsys,ihs_axi";
			reg = <0x170 0x10>;
			little-endian;
			fpga_interrupts = <22>;

			fpga0_dp_video0: fpga0_dp_video0 {
				compatible = "gdsys,logicore_dp_tx";
				reg = <0x44a10000 0x1000>;
				little-endian;
				redriver = <&fpga0_dp_video0_redriver>;
				video_id = <0>;
			};
		};

		fpga0_video1 {
			compatible = "gdsys,ihs_video_out";
			reg = <0x200 0x40>;
			little-endian;
			fpga_interrupts = <2 9>; /* VIDEO OSD */
			osd_base = <0x280>;
			osd_buffer_base = <0x2000>;
			spdif_audio_base = <0x2e0>;
			video_index = <1>;
			video_id = <1>;
			fpga-force-pos-pol;
			sync-source;
			fpga-pb-pixels = <2730>; /* 8192 / 3 */
			fpga-ra-lines = <2>;
			video_tx = <&fpga0_dp_video1>;
			clk_gen = <&fpga0_video1_clkgen>;
			ddc_ci = <&fpga0_dp_video1>;
		};

		fpga0_iic_video1  {
			compatible = "gdsys,ihs_i2cmaster";
			reg = <0x2c0 0x10>;
			little-endian;
			fpga_interrupts = <7>;
			#address-cells = <1>;
			#size-cells = <0>;

			fpga0_video1_clkgen: fpga0_video1_clkgen {
				compatible = "idt,ics8n3qv01";
				reg = <0x6e>;
				channel = <1>;
			};
		};

		fpga0_axi_video1 {
			#address-cells = <1>;
			#size-cells = <1>;
			compatible = "gdsys,ihs_axi";
			reg = <0x270 0x10>;
			little-endian;
			fpga_interrupts = <23>;

			fpga0_dp_video1: fpga0_dp_video1 {
				compatible = "gdsys,logicore_dp_tx";
				reg = <0x44a10000 0x1000>;
				little-endian;
				redriver = <&fpga0_dp_video1_redriver>;
				video_id = <1>;
			};
		};

		fpga0_iic_usb {
			compatible = "gdsys,ihs_i2cmaster";
			reg = <0xb0 0x10>;
			little-endian;
			fpga_interrupts = <24>;
			#address-cells = <1>;
			#size-cells = <0>;

			pca9555@20 {
				compatible = "nxp,pca9555";
				reg = <0x20>;
				#gpio-cells = <2>;
				gpio-controller;
			};
		};

		fpga0_ep0 {
			compatible = "gdsys,io-endpoint";
			reg = < 0x020 0x10
				0x320 0x10
				0x340 0x10
				0x360 0x10>;
			little-endian;
			irq-model-local;
			fpga_interrupts = <12 13 14 15>;
			pollcycle = <200>;
			nprot_channel = <16>;
			uart_line = <0>;
			ep_index = <0>;
			line_protocol = <1>;
		};

		fpga0_mdio {
			compatible = "gdsys,ihs_mdiomaster";
			reg = <0x0058 0x10>;
			little-endian;
			fpga_interrupts = <16>;
			#address-cells = <1>;
			#size-cells = <0>;

			fpga0_phy0 {
				compatible = "ethernet-phy-ieee802.3-c45";
				device_type ="ethernet-phy";
				reg = <0>;
			};
			fpga0_phy1 {
				compatible = "ethernet-phy-ieee802.3-c45";
				device_type ="ethernet-phy";
				reg = <1>;
			};
			fpga0_phy2 {
				compatible = "ethernet-phy-ieee802.3-c45";
				device_type ="ethernet-phy";
				reg = <2>;
			};
			fpga0_phy3 {
				compatible = "ethernet-phy-ieee802.3-c45";
				device_type ="ethernet-phy";
				reg = <3>;
			};
		};

	};


	FPGA1BUS: fpga1bus {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges = <0 0 0x00002000>;

		compatible = "gdsys,soc";

		fpga1_uart_usb {
			compatible = "gdsys,ihs_simple_uart";
			reg = <0xa0 0x08>;
			little-endian;
			fpga_interrupts = <21>;
			line = <4>; /* TODO check and FIX */
		};

		fpga1_iic_main {
			compatible = "gdsys,ihs_i2cmaster";
			reg = <0x60 0x10>;
			little-endian;
			fpga_interrupts = <5>;
			#address-cells = <1>;
			#size-cells = <0>;

			fpga1_dp_video0_redriver: fpga1_dp_video0_redriver {
				compatible = "ti,sn75dp130";
				reg = <0x2c>;
				eq-i2c-enable = <3 2 1 0
						 3 2 1 0
						 3 2 1 0
						 3 2 1 0>; /* 3.5 dB for all pe values for all lanes */
			};
			fpga1_dp_video1_redriver: fpga1_dp_video1_redriver {
				compatible = "ti,sn75dp130";
				reg = <0x2e>;
				eq-i2c-enable = <3 2 1 0
						 3 2 1 0
						 3 2 1 0
						 3 2 1 0>; /* 3.5 dB for all pe values for all lanes */
			};
			lm77@48 {
				compatible = "national,lm77";
				reg = <0x48>;
			};
			ads1015@49 {
				compatible = "ti,ads1015";
				reg = <0x49>;
			};
			ads1015@4b {
				compatible = "ti,ads1015";
				reg = <0x4b>;
			};
		};

		fpga1_video0 {
			compatible = "gdsys,ihs_video_out";
			reg = <0x100 0x40>;
			little-endian;
			fpga_interrupts = <1 8>; /* VIDEO OSD */
			osd_base = <0x180>;
			osd_buffer_base = <0x1000>;
			spdif_audio_base = <0x1e0>;
			video_index = <0>;
			video_id = <4>;
			fpga-force-pos-pol;
			sync-source;
			fpga-pb-pixels = <2730>; /* 8192 / 3 */
			fpga-ra-lines = <2>;
			video_tx = <&fpga1_dp_video0>;
			clk_gen = <&fpga1_video0_clkgen>;
			ddc_ci = <&fpga1_dp_video0>;
		};

		fpga1_iic_video0  {
			compatible = "gdsys,ihs_i2cmaster";
			reg = <0x1c0 0x10>;
			little-endian;
			fpga_interrupts = <6>;
			#address-cells = <1>;
			#size-cells = <0>;

			fpga1_video0_clkgen: fpga1_video0_clkgen {
				compatible = "idt,ics8n3qv01";
				reg = <0x6e>;
				channel = <4>;
			};
		};

		fpga1_axi_video0 {
			#address-cells = <1>;
			#size-cells = <1>;
			compatible = "gdsys,ihs_axi";
			reg = <0x170 0x10>;
			little-endian;
			fpga_interrupts = <22>;

			fpga1_dp_video0: fpga1_dp_video0 {
				compatible = "gdsys,logicore_dp_tx";
				reg = <0x44a10000 0x1000>;
				little-endian;
				redriver = <&fpga1_dp_video0_redriver>;
				video_id = <4>;
			};
		};

		fpga1_video1 {
			compatible = "gdsys,ihs_video_out";
			reg = <0x200 0x40>;
			little-endian;
			fpga_interrupts = <2 9>; /* VIDEO OSD */
			osd_base = <0x280>;
			osd_buffer_base = <0x2000>;
			spdif_audio_base = <0x2e0>;
			video_index = <1>;
			video_id = <5>;
			fpga-force-pos-pol;
			sync-source;
			fpga-pb-pixels = <2730>; /* 8192 / 3 */
			fpga-ra-lines = <2>;
			video_tx = <&fpga1_dp_video1>;
			clk_gen = <&fpga1_video1_clkgen>;
			ddc_ci = <&fpga1_dp_video1>;
		};

		fpga1_iic_video1  {
			compatible = "gdsys,ihs_i2cmaster";
			reg = <0x2c0 0x10>;
			little-endian;
			fpga_interrupts = <7>;
			#address-cells = <1>;
			#size-cells = <0>;

			fpga1_video1_clkgen: fpga1_video1_clkgen {
				compatible = "idt,ics8n3qv01";
				reg = <0x6e>;
				channel = <5>;
			};
		};

		fpga1_axi_video1 {
			#address-cells = <1>;
			#size-cells = <1>;
			compatible = "gdsys,ihs_axi";
			reg = <0x270 0x10>;
			little-endian;
			fpga_interrupts = <23>;

			fpga1_dp_video1: fpga1_dp_video1 {
				compatible = "gdsys,logicore_dp_tx";
				reg = <0x44a10000 0x1000>;
				little-endian;
				redriver = <&fpga1_dp_video1_redriver>;
				video_id = <5>;
			};
		};

		fpga1_iic_usb {
			compatible = "gdsys,ihs_i2cmaster";
			reg = <0xb0 0x10>;
			little-endian;
			fpga_interrupts = <24>;
			#address-cells = <1>;
			#size-cells = <0>;

			pca9555@20 {
				compatible = "nxp,pca9555";
				reg = <0x20>;
				#gpio-cells = <2>;
				gpio-controller;
			};
		};

		fpga1_ep0 {
			compatible = "gdsys,io-endpoint";
			reg = < 0x020 0x10
				0x320 0x10
				0x340 0x10
				0x360 0x10>;
			little-endian;
			irq-model-local;
			fpga_interrupts = <12 13 14 15>;
			pollcycle = <200>;
			nprot_channel = <17>;
			uart_line = <1>;
			ep_index = <0>;
			line_protocol = <1>;
		};

		fpga1_mdio {
			compatible = "gdsys,ihs_mdiomaster";
			reg = <0x0058 0x10>;
			little-endian;
			fpga_interrupts = <16>;
			#address-cells = <1>;
			#size-cells = <0>;

			fpga1_phy0 {
				compatible = "ethernet-phy-ieee802.3-c45";
				device_type ="ethernet-phy";
				reg = <0>;
			};
			fpga1_phy1 {
				compatible = "ethernet-phy-ieee802.3-c45";
				device_type ="ethernet-phy";
				reg = <1>;
			};
			fpga1_phy2 {
				compatible = "ethernet-phy-ieee802.3-c45";
				device_type ="ethernet-phy";
				reg = <2>;
			};
			fpga1_phy3 {
				compatible = "ethernet-phy-ieee802.3-c45";
				device_type ="ethernet-phy";
				reg = <3>;
			};
		};

	};

};

#include "gdsys/gazerbeam-uboot.dtsi"